//***************************************************************************** // (c) Copyright 2006-2009 Xilinx, Inc. All rights reserved. // // This file contains confidential and proprietary information // of Xilinx, Inc. and is protected under U.S. and // international copyright and other intellectual property // laws. // // DISCLAIMER // This disclaimer is not a license and does not grant any // rights to the materials distributed herewith. Except as // otherwise provided in a valid license issued to you by // Xilinx, and to the maximum extent permitted by applicable // law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND // WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES // AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING // BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON- // INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and // (2) Xilinx shall not be liable (whether in contract or tort, // including negligence, or under any other theory of // liability) for any loss or damage of any kind or nature // related to, arising under or in connection with these // materials, including for any direct, or any indirect, // special, incidental, or consequential loss or damage // (including loss of data, profits, goodwill, or any type of // loss or damage suffered as a result of any action brought // by a third party) even if such damage or loss was // reasonably foreseeable or Xilinx had been advised of the // possibility of the same. // // CRITICAL APPLICATIONS // Xilinx products are not designed or intended to be fail- // safe, or for use in any application requiring fail-safe // performance, such as life-support or safety devices or // systems, Class III medical devices, nuclear facilities, // applications related to the deployment of airbags, or any // other applications that could lead to death, personal // injury, or severe property or environmental damage // (individually and collectively, "Critical // Applications"). Customer assumes the sole risk and // liability of any use of Xilinx products in Critical // Applications, subject only to applicable laws and // regulations governing limitations on product liability. // // THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS // PART OF THIS FILE AT ALL TIMES. //***************************************************************************** // ____ ____ // / /\/ / // /___/ \ / Vendor: Xilinx // \ \ \/ Version: 3.6 // \ \ Application: MIG // / / Filename: ddr2_phy_calib.v // /___/ /\ Date Last Modified: $Date: 2010/06/29 12:03:43 $ // \ \ / \ Date Created: Thu Aug 10 2006 // \___\/\___\ // //Device: Virtex-5 //Design Name: DDR2 //Purpose: // This module handles calibration after memory initialization. //Reference: //Revision History: // Rev 1.1 - Default statement is added for the CASE statement of // rdd_mux_sel logic. PK. 03/23/09 // Rev 1.2 - Change training pattern detected for stage 3 calibration. // Use 2-bits per DQS group for stage 3 pattern detection. // RC. 09/21/09 //***************************************************************************** `timescale 1ns/1ps module ddr2_phy_calib # ( // Following parameters are for 72-bit RDIMM design (for ML561 Reference // board design). Actual values may be different. Actual parameters values // are passed from design top module dram module. Please refer to // the dram module for actual values. parameter DQ_WIDTH = 72, parameter DQ_BITS = 7, parameter DQ_PER_DQS = 8, parameter DQS_BITS = 4, parameter DQS_WIDTH = 9, parameter ADDITIVE_LAT = 0, parameter CAS_LAT = 5, parameter REG_ENABLE = 1, parameter CLK_PERIOD = 3000, parameter SIM_ONLY = 0, parameter DEBUG_EN = 0 ) ( input clk, input clkdiv, input rstdiv, input [3:0] calib_start, input ctrl_rden, input phy_init_rden, input [DQ_WIDTH-1:0] rd_data_rise, input [DQ_WIDTH-1:0] rd_data_fall, input calib_ref_done, output reg [3:0] calib_done, output reg calib_ref_req, output [DQS_WIDTH-1:0] calib_rden, output reg [DQS_WIDTH-1:0] calib_rden_sel, output reg dlyrst_dq, output reg [DQ_WIDTH-1:0] dlyce_dq, output reg [DQ_WIDTH-1:0] dlyinc_dq, output reg dlyrst_dqs, output reg [DQS_WIDTH-1:0] dlyce_dqs, output reg [DQS_WIDTH-1:0] dlyinc_dqs, output reg [DQS_WIDTH-1:0] dlyrst_gate, output reg [DQS_WIDTH-1:0] dlyce_gate, output reg [DQS_WIDTH-1:0] dlyinc_gate, //(* XIL_PAR_NO_REG_ORDER = "TRUE", XIL_PAR_PATH="Q->u_iodelay_dq_ce.DATAIN", syn_keep = "1", keep = "TRUE"*) output [DQS_WIDTH-1:0] en_dqs, output [DQS_WIDTH-1:0] rd_data_sel, // Debug signals (optional use) input dbg_idel_up_all, input dbg_idel_down_all, input dbg_idel_up_dq, input dbg_idel_down_dq, input dbg_idel_up_dqs, input dbg_idel_down_dqs, input dbg_idel_up_gate, input dbg_idel_down_gate, input [DQ_BITS-1:0] dbg_sel_idel_dq, input dbg_sel_all_idel_dq, input [DQS_BITS:0] dbg_sel_idel_dqs, input dbg_sel_all_idel_dqs, input [DQS_BITS:0] dbg_sel_idel_gate, input dbg_sel_all_idel_gate, output [3:0] dbg_calib_done, output [3:0] dbg_calib_err, output [(6*DQ_WIDTH)-1:0] dbg_calib_dq_tap_cnt, output [(6*DQS_WIDTH)-1:0] dbg_calib_dqs_tap_cnt, output [(6*DQS_WIDTH)-1:0] dbg_calib_gate_tap_cnt, output [DQS_WIDTH-1:0] dbg_calib_rd_data_sel, output [(5*DQS_WIDTH)-1:0] dbg_calib_rden_dly, output [(5*DQS_WIDTH)-1:0] dbg_calib_gate_dly ); // minimum time (in IDELAY taps) for which capture data must be stable for // algorithm to consider localparam MIN_WIN_SIZE = 5; // IDEL_SET_VAL = (# of cycles - 1) to wait after changing IDELAY value // we only have to wait enough for input with new IDELAY value to // propagate through pipeline stages. localparam IDEL_SET_VAL = 3'b111; // # of clock cycles to delay read enable to determine if read data pattern // is correct for stage 3/4 (RDEN, DQS gate) calibration localparam CALIB_RDEN_PIPE_LEN = 31; // translate CAS latency into number of clock cycles for read valid delay // determination. Really only needed for CL = 2.5 (set to 2) localparam CAS_LAT_RDEN = (CAS_LAT == 25) ? 2 : CAS_LAT; // an SRL32 is used to delay CTRL_RDEN to generate read valid signal. This // is min possible value delay through SRL32 can be localparam RDEN_BASE_DELAY = CAS_LAT_RDEN + ADDITIVE_LAT + REG_ENABLE; // an SRL32 is used to delay the CTRL_RDEN from the read postamble DQS // gate. This is min possible value the SRL32 delay can be: // - Delay from end of deassertion of CTRL_RDEN to last falling edge of // read burst = 3.5 (CTRL_RDEN -> CAS delay) + 3 (min CAS latency) = 6.5 // - Minimum time for DQS gate circuit to be generated: // * 1 cyc to register CTRL_RDEN from controller // * 1 cyc after RDEN_CTRL falling edge // * 1 cyc min through SRL32 // * 1 cyc through SRL32 output flop // * 0 (<1) cyc of synchronization to DQS domain via IDELAY // * 1 cyc of delay through IDDR to generate CE to DQ IDDR's // Total = 5 cyc < 6.5 cycles // The total should be less than 5.5 cycles to account prop delays // adding one cycle to the synchronization time via the IDELAY. // NOTE: Value differs because of optional pipeline register added // for case of RDEN_BASE_DELAY > 3 to improve timing localparam GATE_BASE_DELAY = RDEN_BASE_DELAY - 3; localparam GATE_BASE_INIT = (GATE_BASE_DELAY <= 1) ? 0 : GATE_BASE_DELAY; // used for RDEN calibration: difference between shift value used during // calibration, and shift value for actual RDEN SRL. Only applies when // RDEN edge is immediately captured by CLKDIV0. If not (depends on phase // of CLK0 and CLKDIV0 when RDEN is asserted), then add 1 to this value. localparam CAL3_RDEN_SRL_DLY_DELTA = 6; // fix minimum value of DQS to be 1 to handle the case where's there's only // one DQS group. We could also enforce that user always inputs minimum // value of 1 for DQS_BITS (even when DQS_WIDTH=1). Leave this as safeguard // Assume we don't have to do this for DQ, DQ_WIDTH always > 1 localparam DQS_BITS_FIX = (DQS_BITS == 0) ? 1 : DQS_BITS; // how many taps to "pre-delay" DQ before stg 1 calibration - not needed for // current calibration, but leave for debug localparam DQ_IDEL_INIT = 6'b000000; // # IDELAY taps per bit time (i.e. half cycle). Limit to 63. localparam integer BIT_TIME_TAPS = (CLK_PERIOD/150 < 64) ? CLK_PERIOD/150 : 63; // used in various places during stage 4 cal: (1) determines maximum taps // to increment when finding right edge, (2) amount to decrement after // finding left edge, (3) amount to increment after finding right edge localparam CAL4_IDEL_BIT_VAL = (BIT_TIME_TAPS >= 6'b100000) ? 6'b100000 : BIT_TIME_TAPS; localparam CAL1_IDLE = 4'h0; localparam CAL1_INIT = 4'h1; localparam CAL1_INC_IDEL = 4'h2; localparam CAL1_FIND_FIRST_EDGE = 4'h3; localparam CAL1_FIRST_EDGE_IDEL_WAIT = 4'h4; localparam CAL1_FOUND_FIRST_EDGE_WAIT = 4'h5; localparam CAL1_FIND_SECOND_EDGE = 4'h6; localparam CAL1_SECOND_EDGE_IDEL_WAIT = 4'h7; localparam CAL1_CALC_IDEL = 4'h8; localparam CAL1_DEC_IDEL = 4'h9; localparam CAL1_DONE = 4'hA; localparam CAL2_IDLE = 4'h0; localparam CAL2_INIT = 4'h1; localparam CAL2_INIT_IDEL_WAIT = 4'h2; localparam CAL2_FIND_EDGE_POS = 4'h3; localparam CAL2_FIND_EDGE_IDEL_WAIT_POS = 4'h4; localparam CAL2_FIND_EDGE_NEG = 4'h5; localparam CAL2_FIND_EDGE_IDEL_WAIT_NEG = 4'h6; localparam CAL2_DEC_IDEL = 4'h7; localparam CAL2_DONE = 4'h8; localparam CAL3_IDLE = 3'h0; localparam CAL3_INIT = 3'h1; localparam CAL3_DETECT = 3'h2; localparam CAL3_RDEN_PIPE_CLR_WAIT = 3'h3; localparam CAL3_DONE = 3'h4; localparam CAL4_IDLE = 3'h0; localparam CAL4_INIT = 3'h1; localparam CAL4_FIND_WINDOW = 3'h2; localparam CAL4_FIND_EDGE = 3'h3; localparam CAL4_IDEL_WAIT = 3'h4; localparam CAL4_RDEN_PIPE_CLR_WAIT = 3'h5; localparam CAL4_ADJ_IDEL = 3'h6; localparam CAL4_DONE = 3'h7; integer i, j; reg [5:0] cal1_bit_time_tap_cnt; reg [1:0] cal1_data_chk_last; reg cal1_data_chk_last_valid; reg [1:0] cal1_data_chk_r; reg cal1_dlyce_dq; reg cal1_dlyinc_dq; reg cal1_dqs_dq_init_phase; reg cal1_detect_edge; reg cal1_detect_stable; reg cal1_found_second_edge; reg cal1_found_rising; reg cal1_found_window; reg cal1_first_edge_done; reg [5:0] cal1_first_edge_tap_cnt; reg [6:0] cal1_idel_dec_cnt; reg [5:0] cal1_idel_inc_cnt; reg [5:0] cal1_idel_max_tap; reg cal1_idel_max_tap_we; reg [5:0] cal1_idel_tap_cnt; reg cal1_idel_tap_limit_hit; reg [6:0] cal1_low_freq_idel_dec; reg cal1_ref_req; wire cal1_refresh; reg [3:0] cal1_state; reg [3:0] cal1_window_cnt; reg cal2_curr_sel; wire cal2_detect_edge; reg cal2_dlyce_dqs; reg cal2_dlyinc_dqs; reg [5:0] cal2_idel_dec_cnt; reg [5:0] cal2_idel_tap_cnt; reg [5:0] cal2_idel_tap_limit; reg cal2_idel_tap_limit_hit; reg cal2_rd_data_fall_last_neg; reg cal2_rd_data_fall_last_pos; reg cal2_rd_data_last_valid_neg; reg cal2_rd_data_last_valid_pos; reg cal2_rd_data_rise_last_neg; reg cal2_rd_data_rise_last_pos; reg [DQS_WIDTH-1:0] cal2_rd_data_sel; wire cal2_rd_data_sel_edge; reg [DQS_WIDTH-1:0] cal2_rd_data_sel_r; reg cal2_ref_req; reg [3:0] cal2_state; reg cal3_data_match; reg cal3_data_match_stgd; wire cal3_data_valid; wire cal3_match_found; wire [4:0] cal3_rden_dly; reg [4:0] cal3_rden_srl_a; reg [2:0] cal3_state; wire cal4_data_good; reg cal4_data_match; reg cal4_data_match_stgd; wire cal4_data_valid; reg cal4_dlyce_gate; reg cal4_dlyinc_gate; reg cal4_dlyrst_gate; reg [4:0] cal4_gate_srl_a; reg [5:0] cal4_idel_adj_cnt; reg cal4_idel_adj_inc; reg cal4_idel_bit_tap; reg [5:0] cal4_idel_tap_cnt; reg cal4_idel_max_tap; reg [4:0] cal4_rden_srl_a; reg cal4_ref_req; reg cal4_seek_left; reg cal4_stable_window; reg [2:0] cal4_state; reg [3:0] cal4_window_cnt; reg [3:0] calib_done_tmp; // only for stg1/2/4 reg calib_ctrl_gate_pulse_r; reg calib_ctrl_rden; reg calib_ctrl_rden_r; wire calib_ctrl_rden_negedge; reg calib_ctrl_rden_negedge_r; reg [3:0] calib_done_r; reg [3:0] calib_err; reg [1:0] calib_err_2; wire calib_init_gate_pulse; reg calib_init_gate_pulse_r; reg calib_init_gate_pulse_r1; reg calib_init_rden; reg calib_init_rden_r; reg [4:0] calib_rden_srl_a; wire [4:0] calib_rden_srl_a_r; reg [(5*DQS_WIDTH)-1:0] calib_rden_dly; reg calib_rden_edge_r; reg [4:0] calib_rden_pipe_cnt; wire calib_rden_srl_out; wire calib_rden_srl_out_r; reg calib_rden_srl_out_r1; reg calib_rden_valid; reg calib_rden_valid_stgd; reg [DQ_BITS-1:0] count_dq; reg [DQS_BITS_FIX-1:0] count_dqs; reg [DQS_BITS_FIX-1:0] count_gate; reg [DQS_BITS_FIX-1:0] count_rden; reg ctrl_rden_r; wire dlyce_or; reg [(5*DQS_WIDTH)-1:0] gate_dly; wire [(5*DQS_WIDTH)-1:0] gate_dly_r; wire gate_srl_in; wire [DQS_WIDTH-1:0] gate_srl_out; wire [DQS_WIDTH-1:0] gate_srl_out_r; reg [2:0] idel_set_cnt; wire idel_set_wait; reg [DQ_BITS-1:0] next_count_dq; reg [DQS_BITS_FIX-1:0] next_count_dqs; reg [DQS_BITS_FIX-1:0] next_count_gate; reg phy_init_rden_r; reg phy_init_rden_r1; reg [DQS_WIDTH-1:0] rd_data_fall_1x_bit1_r1; reg [DQ_WIDTH-1:0] rd_data_fall_1x_r; reg [DQS_WIDTH-1:0] rd_data_fall_1x_r1; reg [DQS_WIDTH-1:0] rd_data_fall_2x_bit1_r; reg [DQS_WIDTH-1:0] rd_data_fall_2x_r; wire [DQS_WIDTH-1:0] rd_data_fall_chk_q1; wire [DQS_WIDTH-1:0] rd_data_fall_chk_q1_bit1; wire [DQS_WIDTH-1:0] rd_data_fall_chk_q2; wire [DQS_WIDTH-1:0] rd_data_fall_chk_q2_bit1; reg [DQS_WIDTH-1:0] rd_data_rise_1x_bit1_r1; reg [DQ_WIDTH-1:0] rd_data_rise_1x_r; reg [DQS_WIDTH-1:0] rd_data_rise_1x_r1; reg [DQS_WIDTH-1:0] rd_data_rise_2x_bit1_r; reg [DQS_WIDTH-1:0] rd_data_rise_2x_r; wire [DQS_WIDTH-1:0] rd_data_rise_chk_q1; wire [DQS_WIDTH-1:0] rd_data_rise_chk_q1_bit1; wire [DQS_WIDTH-1:0] rd_data_rise_chk_q2; wire [DQS_WIDTH-1:0] rd_data_rise_chk_q2_bit1; reg rdd_fall_q1; reg rdd_fall_q1_bit1; reg rdd_fall_q1_bit1_r; reg rdd_fall_q1_bit1_r1; reg rdd_fall_q1_r; reg rdd_fall_q1_r1; reg rdd_fall_q2; reg rdd_fall_q2_bit1; reg rdd_fall_q2_bit1_r; reg rdd_fall_q2_r; reg rdd_rise_q1; reg rdd_rise_q1_bit1; reg rdd_rise_q1_bit1_r; reg rdd_rise_q1_bit1_r1; reg rdd_rise_q1_r; reg rdd_rise_q1_r1; reg rdd_rise_q2; reg rdd_rise_q2_bit1; reg rdd_rise_q2_bit1_r; reg rdd_rise_q2_r; reg [DQS_BITS_FIX-1:0] rdd_mux_sel; reg rden_dec; reg [(5*DQS_WIDTH)-1:0] rden_dly; wire [(5*DQS_WIDTH)-1:0] rden_dly_r; reg [4:0] rden_dly_0; reg rden_inc; reg [DQS_WIDTH-1:0] rden_mux; wire [DQS_WIDTH-1:0] rden_srl_out; // Debug integer x; reg [5:0] dbg_dq_tap_cnt [DQ_WIDTH-1:0]; reg [5:0] dbg_dqs_tap_cnt [DQS_WIDTH-1:0]; reg [5:0] dbg_gate_tap_cnt [DQS_WIDTH-1:0]; //*************************************************************************** // Debug output ("dbg_phy_calib_*") // NOTES: // 1. All debug outputs coming out of PHY_CALIB are clocked off CLKDIV0, // although they are also static after calibration is complete. This // means the user can either connect them to a Chipscope ILA, or to // either a sync/async VIO input block. Using an async VIO has the // advantage of not requiring these paths to meet cycle-to-cycle timing. // 2. The widths of most of these debug buses are dependent on the # of // DQS/DQ bits (e.g. dq_tap_cnt width = 6 * (# of DQ bits) // SIGNAL DESCRIPTION: // 1. calib_done: 4 bits - each one asserted as each phase of calibration // is completed. // 2. calib_err: 4 bits - each one asserted when a calibration error // encountered for that stage. Some of these bits may not // be used (not all cal stages report an error). // 3. dq_tap_cnt: final IDELAY tap counts for all DQ IDELAYs // 4. dqs_tap_cnt: final IDELAY tap counts for all DQS IDELAYs // 5. gate_tap_cnt: final IDELAY tap counts for all DQS gate // synchronization IDELAYs // 6. rd_data_sel: final read capture MUX (either "positive" or "negative" // edge capture) settings for all DQS groups // 7. rden_dly: related to # of cycles after issuing a read until when // read data is valid - for all DQS groups // 8. gate_dly: related to # of cycles after issuing a read until when // clock enable for all DQ's is deasserted to prevent // effect of DQS postamble glitch - for all DQS groups //*************************************************************************** //***************************************************************** // Record IDELAY tap values by "snooping" IDELAY control signals //***************************************************************** // record DQ IDELAY tap values genvar dbg_dq_tc_i; generate for (dbg_dq_tc_i = 0; dbg_dq_tc_i < DQ_WIDTH; dbg_dq_tc_i = dbg_dq_tc_i + 1) begin: gen_dbg_dq_tap_cnt assign dbg_calib_dq_tap_cnt[(6*dbg_dq_tc_i)+5:(6*dbg_dq_tc_i)] = dbg_dq_tap_cnt[dbg_dq_tc_i]; always @(posedge clkdiv) if (rstdiv | dlyrst_dq) dbg_dq_tap_cnt[dbg_dq_tc_i] <= 6'b000000; else if (dlyce_dq[dbg_dq_tc_i]) if (dlyinc_dq[dbg_dq_tc_i]) dbg_dq_tap_cnt[dbg_dq_tc_i] <= dbg_dq_tap_cnt[dbg_dq_tc_i] + 1; else dbg_dq_tap_cnt[dbg_dq_tc_i] <= dbg_dq_tap_cnt[dbg_dq_tc_i] - 1; end endgenerate // record DQS IDELAY tap values genvar dbg_dqs_tc_i; generate for (dbg_dqs_tc_i = 0; dbg_dqs_tc_i < DQS_WIDTH; dbg_dqs_tc_i = dbg_dqs_tc_i + 1) begin: gen_dbg_dqs_tap_cnt assign dbg_calib_dqs_tap_cnt[(6*dbg_dqs_tc_i)+5:(6*dbg_dqs_tc_i)] = dbg_dqs_tap_cnt[dbg_dqs_tc_i]; always @(posedge clkdiv) if (rstdiv | dlyrst_dqs) dbg_dqs_tap_cnt[dbg_dqs_tc_i] <= 6'b000000; else if (dlyce_dqs[dbg_dqs_tc_i]) if (dlyinc_dqs[dbg_dqs_tc_i]) dbg_dqs_tap_cnt[dbg_dqs_tc_i] <= dbg_dqs_tap_cnt[dbg_dqs_tc_i] + 1; else dbg_dqs_tap_cnt[dbg_dqs_tc_i] <= dbg_dqs_tap_cnt[dbg_dqs_tc_i] - 1; end endgenerate // record DQS gate IDELAY tap values genvar dbg_gate_tc_i; generate for (dbg_gate_tc_i = 0; dbg_gate_tc_i < DQS_WIDTH; dbg_gate_tc_i = dbg_gate_tc_i + 1) begin: gen_dbg_gate_tap_cnt assign dbg_calib_gate_tap_cnt[(6*dbg_gate_tc_i)+5:(6*dbg_gate_tc_i)] = dbg_gate_tap_cnt[dbg_gate_tc_i]; always @(posedge clkdiv) if (rstdiv | dlyrst_gate[dbg_gate_tc_i]) dbg_gate_tap_cnt[dbg_gate_tc_i] <= 6'b000000; else if (dlyce_gate[dbg_gate_tc_i]) if (dlyinc_gate[dbg_gate_tc_i]) dbg_gate_tap_cnt[dbg_gate_tc_i] <= dbg_gate_tap_cnt[dbg_gate_tc_i] + 1; else dbg_gate_tap_cnt[dbg_gate_tc_i] <= dbg_gate_tap_cnt[dbg_gate_tc_i] - 1; end endgenerate assign dbg_calib_done = calib_done; assign dbg_calib_err = calib_err; assign dbg_calib_rd_data_sel = cal2_rd_data_sel; assign dbg_calib_rden_dly = rden_dly; assign dbg_calib_gate_dly = gate_dly; //*************************************************************************** // Read data pipelining, and read data "ISERDES" data width expansion //*************************************************************************** // For all data bits, register incoming capture data to slow clock to improve // timing. Adding single pipeline stage does not affect functionality (as // long as we make sure to wait extra clock cycle after changing DQ IDELAY) // Also note in this case that we're "missing" every other clock cycle's // worth of data capture since we're sync'ing to the slow clock. This is // fine for stage 1 and stage 2 cal, but not for stage 3 and 4 (see below // for different circuit to handle those stages) always @(posedge clkdiv) begin rd_data_rise_1x_r <= rd_data_rise; rd_data_fall_1x_r <= rd_data_fall; end // For every DQ_PER_DQS bit, generate what is essentially a ISERDES-type // data width expander. Will need this for stage 3 and 4 cal, where we need // to compare data over consecutive clock cycles. We can also use this for // stage 2 as well (stage 2 doesn't require every bit to be looked at, only // one bit per DQS group) // MIG 3.3: Expand to use lower two bits of each DQS group - use for stage // 3 calibration for added robustness, since we will be checking for the // training pattern from the memory even when the data bus is 3-stated. // Theoretically it is possible for whatever garbage data is on the bus // to be interpreted as the training sequence, although this can be made // very unlikely by the choice of training sequence (bit sequence, length) // and the number of bits compared for each DQS group. genvar rdd_i; generate for (rdd_i = 0; rdd_i < DQS_WIDTH; rdd_i = rdd_i + 1) begin: gen_rdd // first stage: keep data in fast clk domain. Store data over two // consecutive clock cycles for rise/fall data for proper transfer // to slow clock domain always @(posedge clk) begin rd_data_rise_2x_r[rdd_i] <= rd_data_rise[(rdd_i*DQ_PER_DQS)]; rd_data_fall_2x_r[rdd_i] <= rd_data_fall[(rdd_i*DQ_PER_DQS)]; rd_data_rise_2x_bit1_r[rdd_i] <= rd_data_rise[(rdd_i*DQ_PER_DQS)+1]; rd_data_fall_2x_bit1_r[rdd_i] <= rd_data_fall[(rdd_i*DQ_PER_DQS)+1]; end // second stage, register first stage to slow clock domain, 2nd stage // consists of both these flops, and the rd_data_rise_1x_r flops always @(posedge clkdiv) begin rd_data_rise_1x_r1[rdd_i] <= rd_data_rise_2x_r[rdd_i]; rd_data_fall_1x_r1[rdd_i] <= rd_data_fall_2x_r[rdd_i]; rd_data_rise_1x_bit1_r1[rdd_i] <= rd_data_rise_2x_bit1_r[rdd_i]; rd_data_fall_1x_bit1_r1[rdd_i] <= rd_data_fall_2x_bit1_r[rdd_i]; end // now we have four outputs - representing rise/fall outputs over last // 2 fast clock cycles. However, the ordering these represent can either // be: (1) Q2 = data @ time = n, Q1 = data @ time = n+1, or (2) // Q2 = data @ time = n - 1, Q1 = data @ time = n (and data at [Q1,Q2] // is "staggered") - leave it up to the stage of calibration using this // to figure out which is which, if they care at all (e.g. stage 2 cal // doesn't care about the ordering) assign rd_data_rise_chk_q1[rdd_i] = rd_data_rise_1x_r[(rdd_i*DQ_PER_DQS)]; assign rd_data_rise_chk_q2[rdd_i] = rd_data_rise_1x_r1[rdd_i]; assign rd_data_fall_chk_q1[rdd_i] = rd_data_fall_1x_r[(rdd_i*DQ_PER_DQS)]; assign rd_data_fall_chk_q2[rdd_i] = rd_data_fall_1x_r1[rdd_i]; // MIG 3.3: Added comparison for second bit in DQS group for stage 3 cal assign rd_data_rise_chk_q1_bit1[rdd_i] = rd_data_rise_1x_r[(rdd_i*DQ_PER_DQS)+1]; assign rd_data_rise_chk_q2_bit1[rdd_i] = rd_data_rise_1x_bit1_r1[rdd_i]; assign rd_data_fall_chk_q1_bit1[rdd_i] = rd_data_fall_1x_r[(rdd_i*DQ_PER_DQS)+1]; assign rd_data_fall_chk_q2_bit1[rdd_i] = rd_data_fall_1x_bit1_r1[rdd_i]; end endgenerate //***************************************************************** // Outputs of these simplified ISERDES circuits then feed MUXes based on // which DQ the current calibration algorithm needs to look at //***************************************************************** // generate MUX control; assume that adding an extra pipeline stage isn't // an issue - whatever stage cal logic is using output of MUX will wait // enough time after changing it always @(posedge clkdiv) begin (* full_case, parallel_case *) case (calib_done[2:0]) 3'b001: rdd_mux_sel <= next_count_dqs; 3'b011: rdd_mux_sel <= count_rden; 3'b111: rdd_mux_sel <= next_count_gate; default: rdd_mux_sel <= {DQS_BITS_FIX{1'bx}}; endcase end always @(posedge clkdiv) begin rdd_rise_q1 <= rd_data_rise_chk_q1[rdd_mux_sel]; rdd_rise_q2 <= rd_data_rise_chk_q2[rdd_mux_sel]; rdd_fall_q1 <= rd_data_fall_chk_q1[rdd_mux_sel]; rdd_fall_q2 <= rd_data_fall_chk_q2[rdd_mux_sel]; rdd_rise_q1_bit1 <= rd_data_rise_chk_q1_bit1[rdd_mux_sel]; rdd_rise_q2_bit1 <= rd_data_rise_chk_q2_bit1[rdd_mux_sel]; rdd_fall_q1_bit1 <= rd_data_fall_chk_q1_bit1[rdd_mux_sel]; rdd_fall_q2_bit1 <= rd_data_fall_chk_q2_bit1[rdd_mux_sel]; end //*************************************************************************** // Demultiplexor to control (reset, increment, decrement) IDELAY tap values // For DQ: // STG1: for per-bit-deskew, only inc/dec the current DQ. For non-per // deskew, increment all bits in the current DQS set // STG2: inc/dec all DQ's in the current DQS set. // NOTE: Nice to add some error checking logic here (or elsewhere in the // code) to check if logic attempts to overflow tap value //*************************************************************************** // don't use DLYRST to reset value of IDELAY after reset. Need to change this // if we want to allow user to recalibrate after initial reset always @(posedge clkdiv) if (rstdiv) begin dlyrst_dq <= 1'b1; dlyrst_dqs <= 1'b1; end else begin dlyrst_dq <= 1'b0; dlyrst_dqs <= 1'b0; end always @(posedge clkdiv) begin if (rstdiv) begin dlyce_dq <= 'b0; dlyinc_dq <= 'b0; dlyce_dqs <= 'b0; dlyinc_dqs <= 'b0; end else begin dlyce_dq <= 'b0; dlyinc_dq <= 'b0; dlyce_dqs <= 'b0; dlyinc_dqs <= 'b0; // stage 1 cal: change only specified DQ if (cal1_dlyce_dq) begin if (SIM_ONLY == 0) begin dlyce_dq[count_dq] <= 1'b1; dlyinc_dq[count_dq] <= cal1_dlyinc_dq; end else begin // if simulation, then calibrate only first DQ, apply results // to all DQs (i.e. assume delay on all DQs is the same) for (i = 0; i < DQ_WIDTH; i = i + 1) begin: loop_sim_dq_dly dlyce_dq[i] <= 1'b1; dlyinc_dq[i] <= cal1_dlyinc_dq; end end end else if (cal2_dlyce_dqs) begin // stage 2 cal: change DQS and all corresponding DQ's if (SIM_ONLY == 0) begin dlyce_dqs[count_dqs] <= 1'b1; dlyinc_dqs[count_dqs] <= cal2_dlyinc_dqs; for (i = 0; i < DQ_PER_DQS; i = i + 1) begin: loop_dqs_dly dlyce_dq[(DQ_PER_DQS*count_dqs)+i] <= 1'b1; dlyinc_dq[(DQ_PER_DQS*count_dqs)+i] <= cal2_dlyinc_dqs; end end else begin for (i = 0; i < DQS_WIDTH; i = i + 1) begin: loop_sim_dqs_dly // if simulation, then calibrate only first DQS dlyce_dqs[i] <= 1'b1; dlyinc_dqs[i] <= cal2_dlyinc_dqs; for (j = 0; j < DQ_PER_DQS; j = j + 1) begin: loop_sim_dq_dqs_dly dlyce_dq[(DQ_PER_DQS*i)+j] <= 1'b1; dlyinc_dq[(DQ_PER_DQS*i)+j] <= cal2_dlyinc_dqs; end end end end else if (DEBUG_EN != 0) begin // DEBUG: allow user to vary IDELAY tap settings // For DQ IDELAY taps if (dbg_idel_up_all || dbg_idel_down_all || dbg_sel_all_idel_dq) begin for (x = 0; x < DQ_WIDTH; x = x + 1) begin: loop_dly_inc_dq dlyce_dq[x] <= dbg_idel_up_all | dbg_idel_down_all | dbg_idel_up_dq | dbg_idel_down_dq; dlyinc_dq[x] <= dbg_idel_up_all | dbg_idel_up_dq; end end else begin dlyce_dq <= 'b0; dlyce_dq[dbg_sel_idel_dq] <= dbg_idel_up_dq | dbg_idel_down_dq; dlyinc_dq[dbg_sel_idel_dq] <= dbg_idel_up_dq; end // For DQS IDELAY taps if (dbg_idel_up_all || dbg_idel_down_all || dbg_sel_all_idel_dqs) begin for (x = 0; x < DQS_WIDTH; x = x + 1) begin: loop_dly_inc_dqs dlyce_dqs[x] <= dbg_idel_up_all | dbg_idel_down_all | dbg_idel_up_dqs | dbg_idel_down_dqs; dlyinc_dqs[x] <= dbg_idel_up_all | dbg_idel_up_dqs; end end else begin dlyce_dqs <= 'b0; dlyce_dqs[dbg_sel_idel_dqs] <= dbg_idel_up_dqs | dbg_idel_down_dqs; dlyinc_dqs[dbg_sel_idel_dqs] <= dbg_idel_up_dqs; end end end end // GATE synchronization is handled directly by Stage 4 calibration FSM always @(posedge clkdiv) if (rstdiv) begin dlyrst_gate <= {DQS_WIDTH{1'b1}}; dlyce_gate <= {DQS_WIDTH{1'b0}}; dlyinc_gate <= {DQS_WIDTH{1'b0}}; end else begin dlyrst_gate <= {DQS_WIDTH{1'b0}}; dlyce_gate <= {DQS_WIDTH{1'b0}}; dlyinc_gate <= {DQS_WIDTH{1'b0}}; if (cal4_dlyrst_gate) begin if (SIM_ONLY == 0) dlyrst_gate[count_gate] <= 1'b1; else for (i = 0; i < DQS_WIDTH; i = i + 1) begin: loop_gate_sim_dly_rst dlyrst_gate[i] <= 1'b1; end end if (cal4_dlyce_gate) begin if (SIM_ONLY == 0) begin dlyce_gate[count_gate] <= 1'b1; dlyinc_gate[count_gate] <= cal4_dlyinc_gate; end else begin // if simulation, then calibrate only first gate for (i = 0; i < DQS_WIDTH; i = i + 1) begin: loop_gate_sim_dly dlyce_gate[i] <= 1'b1; dlyinc_gate[i] <= cal4_dlyinc_gate; end end end else if (DEBUG_EN != 0) begin // DEBUG: allow user to vary IDELAY tap settings if (dbg_idel_up_all || dbg_idel_down_all || dbg_sel_all_idel_gate) begin for (x = 0; x < DQS_WIDTH; x = x + 1) begin: loop_dly_inc_gate dlyce_gate[x] <= dbg_idel_up_all | dbg_idel_down_all | dbg_idel_up_gate | dbg_idel_down_gate; dlyinc_gate[x] <= dbg_idel_up_all | dbg_idel_up_gate; end end else begin dlyce_gate <= {DQS_WIDTH{1'b0}}; dlyce_gate[dbg_sel_idel_gate] <= dbg_idel_up_gate | dbg_idel_down_gate; dlyinc_gate[dbg_sel_idel_gate] <= dbg_idel_up_gate; end end end //*************************************************************************** // signal to tell calibration state machines to wait and give IDELAY time to // settle after it's value is changed (both time for IDELAY chain to settle, // and for settled output to propagate through ISERDES). For general use: use // for any calibration state machines that modify any IDELAY. // Should give at least enough time for IDELAY output to settle (technically // for V5, this should be "glitchless" when IDELAY taps are changed, so don't // need any time here), and also time for new data to propagate through both // ISERDES and the "RDD" MUX + associated pipelining // For now, give very "generous" delay - doesn't really matter since only // needed during calibration //*************************************************************************** // determine if calibration polarity has changed always @(posedge clkdiv) cal2_rd_data_sel_r <= cal2_rd_data_sel; assign cal2_rd_data_sel_edge = |(cal2_rd_data_sel ^ cal2_rd_data_sel_r); // combine requests to modify any of the IDELAYs into one. Also when second // stage capture "edge" polarity is changed (IDELAY isn't changed in this // case, but use the same counter to stall cal logic) assign dlyce_or = cal1_dlyce_dq | cal2_dlyce_dqs | cal2_rd_data_sel_edge | cal4_dlyce_gate | cal4_dlyrst_gate; // SYN_NOTE: Can later recode to avoid combinational path assign idel_set_wait = dlyce_or || (idel_set_cnt != IDEL_SET_VAL); always @(posedge clkdiv) if (rstdiv) idel_set_cnt <= 4'b0000; else if (dlyce_or) idel_set_cnt <= 4'b0000; else if (idel_set_cnt != IDEL_SET_VAL) idel_set_cnt <= idel_set_cnt + 1; // generate request to PHY_INIT logic to issue auto-refresh // used by certain states to force prech/auto-refresh part way through // calibration to avoid a tRAS violation (which will happen if that // stage of calibration lasts long enough). This signal must meet the // following requirements: (1) only transition from 0->1 when the refresh // request is needed, (2) stay at 1 and only transition 1->0 when // CALIB_REF_DONE is asserted always @(posedge clkdiv) if (rstdiv) calib_ref_req <= 1'b0; else calib_ref_req <= cal1_ref_req | cal2_ref_req | cal4_ref_req; // stage 1 calibration requests auto-refresh every 4 bits generate if (DQ_BITS < 2) begin: gen_cal1_refresh_dq_lte4 assign cal1_refresh = 1'b0; end else begin: gen_cal1_refresh_dq_gt4 assign cal1_refresh = (next_count_dq[1:0] == 2'b00); end endgenerate //*************************************************************************** // First stage calibration: DQ-DQS // Definitions: // edge: detected when varying IDELAY, and current capture data != prev // capture data // valid bit window: detected when current capture data == prev capture // data for more than half the bit time // starting conditions for DQS-DQ phase: // case 1: when DQS starts somewhere in rising edge bit window, or // on the right edge of the rising bit window. // case 2: when DQS starts somewhere in falling edge bit window, or // on the right edge of the falling bit window. // Algorithm Description: // 1. Increment DQ IDELAY until we find an edge. // 2. While we're finding the first edge, note whether a valid bit window // has been detected before we found an edge. If so, then figure out if // this is the rising or falling bit window. If rising, then our starting // DQS-DQ phase is case 1. If falling, then it's case 2. If don't detect // a valid bit window, then we must have started on the edge of a window. // Need to wait until later on to decide which case we are. // - Store FIRST_EDGE IDELAY value // 3. Now look for second edge. // 4. While we're finding the second edge, note whether valid bit window // is detected. If so, then use to, along with results from (2) to figure // out what the starting case is. If in rising bit window, then we're in // case 2. If falling, then case 1. // - Store SECOND_EDGE IDELAY value // NOTES: // a. Finding two edges allows us to calculate the bit time (although // not the "same" bit time polarity - need to investigate this // more). // b. If we run out of taps looking for the second edge, then the bit // time must be too long (>= 2.5ns, and DQS-DQ starting phase must be // case 1). // 5. Calculate absolute amount to delay DQ as: // If second edge found, and case 1: // - DQ_IDELAY = FIRST_EDGE - 0.5*(SECOND_EDGE - FIRST_EDGE) // If second edge found, and case 2: // - DQ_IDELAY = SECOND_EDGE - 0.5*(SECOND_EDGE - FIRST_EDGE) // If second edge not found, then need to make an approximation on // how much to shift by (should be okay, because we have more timing // margin): // - DQ_IDELAY = FIRST_EDGE - 0.5 * (bit_time) // NOTE: Does this account for either case 1 or case 2????? // NOTE: It's also possible even when we find the second edge, that // to instead just use half the bit time to subtract from either // FIRST or SECOND_EDGE. Finding the actual bit time (which is // what (SECOND_EDGE - FIRST_EDGE) is, is slightly more accurate, // since it takes into account duty cycle distortion. // 6. Repeat for each DQ in current DQS set. //*************************************************************************** //***************************************************************** // for first stage calibration - used for checking if DQS is aligned to the // particular DQ, such that we're in the data valid window. Basically, this // is one giant MUX. // = [falling data, rising data] // = [0, 1] = rising DQS aligned in proper (rising edge) bit window // = [1, 0] = rising DQS aligned in wrong (falling edge) bit window // = [0, 0], or [1,1] = in uncertain region between windows //***************************************************************** // SYN_NOTE: May have to split this up into multiple levels - MUX can get // very wide - as wide as the data bus width always @(posedge clkdiv) cal1_data_chk_r <= {rd_data_fall_1x_r[next_count_dq], rd_data_rise_1x_r[next_count_dq]}; //***************************************************************** // determine when an edge has occurred - when either the current value // is different from the previous latched value or when the DATA_CHK // outputs are the same (rare, but indicates that we're at an edge) // This is only valid when the IDELAY output and propagation of the // data through the capture flops has had a chance to settle out. //***************************************************************** // write CAL1_DETECT_EDGE and CAL1_DETECT_STABLE in such a way that // if X's are captured on the bus during functional simulation, that // the logic will register this as an edge detected. Do this to allow // use of this HDL with Denali memory models (Denali models drive DQ // to X's on both edges of the data valid window to simulate jitter) // This is only done for functional simulation purposes. **Should not** // make the final synthesized logic more complicated, but it does make // the HDL harder to understand b/c we have to "phrase" the logic // slightly differently than when not worrying about X's always @(*) begin // no edge found if: (1) we have recorded prev edge, and rise // data == fall data, (2) we haven't yet recorded prev edge, but // rise/fall data is equal to either [0,1] or [1,0] (i.e. rise/fall // data isn't either X's, or [0,0] or [1,1], which indicates we're // in the middle of an edge, since normally rise != fall data for stg1) if ((cal1_data_chk_last_valid && (cal1_data_chk_r == cal1_data_chk_last)) || (!cal1_data_chk_last_valid && ((cal1_data_chk_r == 2'b01) || (cal1_data_chk_r == 2'b10)))) cal1_detect_edge = 1'b0; else cal1_detect_edge = 1'b1; end always @(*) begin // assert if we've found a region where data valid window is stable // over consecutive IDELAY taps, and either rise/fall = [1,0], or [0,1] if ((cal1_data_chk_last_valid && (cal1_data_chk_r == cal1_data_chk_last)) && ((cal1_data_chk_r == 2'b01) || (cal1_data_chk_r == 2'b10))) cal1_detect_stable = 1'b1; else cal1_detect_stable = 1'b0; end //***************************************************************** // Find valid window: keep track of how long we've been in the same data // window. If it's been long enough, then declare that we've found a valid // window. Also returns whether we found a rising or falling window (only // valid when found_window is asserted) //***************************************************************** always @(posedge clkdiv) begin if (cal1_state == CAL1_INIT) begin cal1_window_cnt <= 4'b0000; cal1_found_window <= 1'b0; cal1_found_rising <= 1'bx; end else if (!cal1_data_chk_last_valid) begin // if we haven't stored a previous value of CAL1_DATA_CHK (or it got // invalidated because we detected an edge, and are now looking for the // second edge), then make sure FOUND_WINDOW deasserted on following // clock edge (to avoid finding a false window immediately after finding // an edge). Note that because of jitter, it's possible to not find an // edge at the end of the IDELAY increment settling time, but to find an // edge on the next clock cycle (e.g. during CAL1_FIND_FIRST_EDGE) cal1_window_cnt <= 4'b0000; cal1_found_window <= 1'b0; cal1_found_rising <= 1'bx; end else if (((cal1_state == CAL1_FIRST_EDGE_IDEL_WAIT) || (cal1_state == CAL1_SECOND_EDGE_IDEL_WAIT)) && !idel_set_wait) begin // while finding the first and second edges, see if we can detect a // stable bit window (occurs over MIN_WIN_SIZE number of taps). If // so, then we're away from an edge, and can conclusively determine the // starting DQS-DQ phase. if (cal1_detect_stable) begin cal1_window_cnt <= cal1_window_cnt + 1; if (cal1_window_cnt == MIN_WIN_SIZE-1) begin cal1_found_window <= 1'b1; if (cal1_data_chk_r == 2'b01) cal1_found_rising <= 1'b1; else cal1_found_rising <= 1'b0; end end else begin // otherwise, we're not in a data valid window, reset the window // counter, and indicate we're not currently in window. This should // happen by design at least once after finding the first edge. cal1_window_cnt <= 4'b0000; cal1_found_window <= 1'b0; cal1_found_rising <= 1'bx; end end end //***************************************************************** // keep track of edge tap counts found, and whether we've // incremented to the maximum number of taps allowed //***************************************************************** always @(posedge clkdiv) if (cal1_state == CAL1_INIT) begin cal1_idel_tap_limit_hit <= 1'b0; cal1_idel_tap_cnt <= 6'b000000; end else if (cal1_dlyce_dq) begin if (cal1_dlyinc_dq) begin cal1_idel_tap_cnt <= cal1_idel_tap_cnt + 1; cal1_idel_tap_limit_hit <= (cal1_idel_tap_cnt == 6'b111110); end else begin cal1_idel_tap_cnt <= cal1_idel_tap_cnt - 1; cal1_idel_tap_limit_hit <= 1'b0; end end //***************************************************************** // Pipeline for better timing - amount to decrement by if second // edge not found //***************************************************************** // if only one edge found (possible for low frequencies), then: // 1. Assume starting DQS-DQ phase has DQS in DQ window (aka "case 1") // 2. We have to decrement by (63 - first_edge_tap_cnt) + (BIT_TIME_TAPS/2) // (i.e. decrement by 63-first_edge_tap_cnt to get to right edge of // DQ window. Then decrement again by (BIT_TIME_TAPS/2) to get to center // of DQ window. // 3. Clamp the above value at 63 to ensure we don't underflow IDELAY // (note: clamping happens in the CAL1 state machine) always @(posedge clkdiv) cal1_low_freq_idel_dec <= (7'b0111111 - {1'b0, cal1_first_edge_tap_cnt}) + (BIT_TIME_TAPS/2); //***************************************************************** // Keep track of max taps used during stage 1, use this to limit // the number of taps that can be used in stage 2 //***************************************************************** always @(posedge clkdiv) if (rstdiv) begin cal1_idel_max_tap <= 6'b000000; cal1_idel_max_tap_we <= 1'b0; end else begin // pipeline latch enable for CAL1_IDEL_MAX_TAP - we have plenty // of time, tap count gets updated, then dead cycles waiting for // IDELAY output to settle cal1_idel_max_tap_we <= (cal1_idel_max_tap < cal1_idel_tap_cnt); // record maximum # of taps used for stg 1 cal if ((cal1_state == CAL1_DONE) && cal1_idel_max_tap_we) cal1_idel_max_tap <= cal1_idel_tap_cnt; end //***************************************************************** always @(posedge clkdiv) if (rstdiv) begin calib_done[0] <= 1'b0; calib_done_tmp[0] <= 1'bx; calib_err[0] <= 1'b0; count_dq <= {DQ_BITS{1'b0}}; next_count_dq <= {DQ_BITS{1'b0}}; cal1_bit_time_tap_cnt <= 6'bxxxxxx; cal1_data_chk_last <= 2'bxx; cal1_data_chk_last_valid <= 1'bx; cal1_dlyce_dq <= 1'b0; cal1_dlyinc_dq <= 1'b0; cal1_dqs_dq_init_phase <= 1'bx; cal1_first_edge_done <= 1'bx; cal1_found_second_edge <= 1'bx; cal1_first_edge_tap_cnt <= 6'bxxxxxx; cal1_idel_dec_cnt <= 7'bxxxxxxx; cal1_idel_inc_cnt <= 6'bxxxxxx; cal1_ref_req <= 1'b0; cal1_state <= CAL1_IDLE; end else begin // default values for all "pulse" outputs cal1_ref_req <= 1'b0; cal1_dlyce_dq <= 1'b0; cal1_dlyinc_dq <= 1'b0; case (cal1_state) CAL1_IDLE: begin count_dq <= {DQ_BITS{1'b0}}; next_count_dq <= {DQ_BITS{1'b0}}; if (calib_start[0]) begin calib_done[0] <= 1'b0; calib_done_tmp[0] <= 1'b0; cal1_state <= CAL1_INIT; end end CAL1_INIT: begin cal1_data_chk_last_valid <= 1'b0; cal1_found_second_edge <= 1'b0; cal1_dqs_dq_init_phase <= 1'b0; cal1_idel_inc_cnt <= 6'b000000; cal1_state <= CAL1_INC_IDEL; end // increment DQ IDELAY so that either: (1) DQS starts somewhere in // first rising DQ window, or (2) DQS starts in first falling DQ // window. The amount to shift is frequency dependent (and is either // precalculated by MIG or possibly adjusted by the user) CAL1_INC_IDEL: if ((cal1_idel_inc_cnt == DQ_IDEL_INIT) && !idel_set_wait) begin cal1_state <= CAL1_FIND_FIRST_EDGE; end else if (cal1_idel_inc_cnt != DQ_IDEL_INIT) begin cal1_idel_inc_cnt <= cal1_idel_inc_cnt + 1; cal1_dlyce_dq <= 1'b1; cal1_dlyinc_dq <= 1'b1; end // look for first edge CAL1_FIND_FIRST_EDGE: begin // Determine DQS-DQ phase if we can detect enough of a valid window if (cal1_found_window) cal1_dqs_dq_init_phase <= ~cal1_found_rising; // find first edge - if found then record position if (cal1_detect_edge) begin cal1_state <= CAL1_FOUND_FIRST_EDGE_WAIT; cal1_first_edge_done <= 1'b0; cal1_first_edge_tap_cnt <= cal1_idel_tap_cnt; cal1_data_chk_last_valid <= 1'b0; end else begin // otherwise, store the current value of DATA_CHK, increment // DQ IDELAY, and compare again cal1_state <= CAL1_FIRST_EDGE_IDEL_WAIT; cal1_data_chk_last <= cal1_data_chk_r; // avoid comparing against DATA_CHK_LAST for previous iteration cal1_data_chk_last_valid <= 1'b1; cal1_dlyce_dq <= 1'b1; cal1_dlyinc_dq <= 1'b1; end end // wait for DQ IDELAY to settle CAL1_FIRST_EDGE_IDEL_WAIT: if (!idel_set_wait) cal1_state <= CAL1_FIND_FIRST_EDGE; // delay state between finding first edge and looking for second // edge. Necessary in order to invalidate CAL1_FOUND_WINDOW before // starting to look for second edge CAL1_FOUND_FIRST_EDGE_WAIT: cal1_state <= CAL1_FIND_SECOND_EDGE; // Try and find second edge CAL1_FIND_SECOND_EDGE: begin // When looking for 2nd edge, first make sure data stabilized (by // detecting valid data window) - needed to avoid false edges if (cal1_found_window) begin cal1_first_edge_done <= 1'b1; cal1_dqs_dq_init_phase <= cal1_found_rising; end // exit if run out of taps to increment if (cal1_idel_tap_limit_hit) cal1_state <= CAL1_CALC_IDEL; else begin // found second edge, record the current edge count if (cal1_first_edge_done && cal1_detect_edge) begin cal1_state <= CAL1_CALC_IDEL; cal1_found_second_edge <= 1'b1; cal1_bit_time_tap_cnt <= cal1_idel_tap_cnt - cal1_first_edge_tap_cnt + 1; end else begin cal1_state <= CAL1_SECOND_EDGE_IDEL_WAIT; cal1_data_chk_last <= cal1_data_chk_r; cal1_data_chk_last_valid <= 1'b1; cal1_dlyce_dq <= 1'b1; cal1_dlyinc_dq <= 1'b1; end end end // wait for DQ IDELAY to settle, then store ISERDES output CAL1_SECOND_EDGE_IDEL_WAIT: if (!idel_set_wait) cal1_state <= CAL1_FIND_SECOND_EDGE; // pipeline delay state to calculate amount to decrement DQ IDELAY // NOTE: We're calculating the amount to decrement by, not the // absolute setting for DQ IDELAY CAL1_CALC_IDEL: begin // if two edges found if (cal1_found_second_edge) // case 1: DQS was in DQ window to start with. First edge found // corresponds to left edge of DQ rising window. Backup by 1.5*BT // NOTE: In this particular case, it is possible to decrement // "below 0" in the case where DQS delay is less than 0.5*BT, // need to limit decrement to prevent IDELAY tap underflow if (!cal1_dqs_dq_init_phase) cal1_idel_dec_cnt <= {1'b0, cal1_bit_time_tap_cnt} + {1'b0, (cal1_bit_time_tap_cnt >> 1)}; // case 2: DQS was in wrong DQ window (in DQ falling window). // First edge found is right edge of DQ rising window. Second // edge is left edge of DQ rising window. Backup by 0.5*BT else cal1_idel_dec_cnt <= {1'b0, (cal1_bit_time_tap_cnt >> 1)}; // if only one edge found - assume will always be case 1 - DQS in // DQS window. Case 2 only possible if path delay on DQS > 5ns else cal1_idel_dec_cnt <= cal1_low_freq_idel_dec; cal1_state <= CAL1_DEC_IDEL; end // decrement DQ IDELAY for final adjustment CAL1_DEC_IDEL: // once adjustment is complete, we're done with calibration for // this DQ, now return to IDLE state and repeat for next DQ // Add underflow protection for case of 2 edges found and DQS // starting in DQ window (see comments for above state) - note we // have to take into account delayed value of CAL1_IDEL_TAP_CNT - // gets updated one clock cycle after CAL1_DLYCE/INC_DQ if ((cal1_idel_dec_cnt == 7'b0000000) || (cal1_dlyce_dq && (cal1_idel_tap_cnt == 6'b000001))) begin cal1_state <= CAL1_DONE; // stop when all DQ's calibrated, or DQ[0] cal'ed (for sim) if ((count_dq == DQ_WIDTH-1) || (SIM_ONLY != 0)) calib_done_tmp[0] <= 1'b1; else // need for VHDL simulation to prevent out-of-index error next_count_dq <= count_dq + 1; end else begin // keep decrementing until final tap count reached cal1_idel_dec_cnt <= cal1_idel_dec_cnt - 1; cal1_dlyce_dq <= 1'b1; cal1_dlyinc_dq <= 1'b0; end // delay state to allow count_dq and DATA_CHK to point to the next // DQ bit (allows us to potentially begin checking for an edge on // next DQ right away). CAL1_DONE: if (!idel_set_wait) begin count_dq <= next_count_dq; if (calib_done_tmp[0]) begin calib_done[0] <= 1'b1; cal1_state <= CAL1_IDLE; end else begin // request auto-refresh after every 8-bits calibrated to // avoid tRAS violation if (cal1_refresh) begin cal1_ref_req <= 1'b1; if (calib_ref_done) cal1_state <= CAL1_INIT; end else // if no need this time for refresh, proceed to next bit cal1_state <= CAL1_INIT; end end endcase end //*************************************************************************** // Second stage calibration: DQS-FPGA Clock // Algorithm Description: // 1. Assumes a training pattern that will produce a pattern oscillating at // half the core clock frequency each on rise and fall outputs, and such // that rise and fall outputs are 180 degrees out of phase from each // other. Note that since the calibration logic runs at half the speed // of the interface, expect that data sampled with the slow clock always // to be constant (either always = 1, or = 0, and rise data != fall data) // unless we cross the edge of the data valid window // 2. Start by setting RD_DATA_SEL = 0. This selects the rising capture data // sync'ed to rising edge of core clock, and falling edge data sync'ed // to falling edge of core clock // 3. Start looking for an edge. An edge is defined as either: (1) a // change in capture value or (2) an invalid capture value (e.g. rising // data != falling data for that same clock cycle). // 4. If an edge is found, go to step (6). If edge hasn't been found, then // set RD_DATA_SEL = 1, and try again. // 5. If no edge is found, then increment IDELAY and return to step (3) // 6. If an edge if found, then invert RD_DATA_SEL - this shifts the // capture point 180 degrees from the edge of the window (minus duty // cycle distortion, delay skew between rising/falling edge capture // paths, etc.) // 7. If no edge is found by CAL2_IDEL_TAP_LIMIT (= 63 - # taps used for // stage 1 calibration), then decrement IDELAY (without reinverting // RD_DATA_SEL) by CAL2_IDEL_TAP_LIMIT/2. This guarantees we at least // have CAL2_IDEL_TAP_LIMIT/2 of slack both before and after the // capture point (not optimal, but best we can do not having found an // of the window). This happens only for very low frequencies. // 8. Repeat for each DQS group. // NOTE: Step 6 is not optimal. A better (and perhaps more complicated) // algorithm might be to find both edges of the data valid window (using // the same polarity of RD_DATA_SEL), and then decrement to the midpoint. //*************************************************************************** // RD_DATA_SEL should be tagged with FROM-TO (multi-cycle) constraint in // UCF file to relax timing. This net is "pseudo-static" (after value is // changed, FSM waits number of cycles before using the output). // Note that we are adding one clock cycle of delay (to isolate it from // the other logic CAL2_RD_DATA_SEL feeds), make sure FSM waits long // enough to compensate (by default it does, it waits a few cycles more // than minimum # of clock cycles) genvar rd_i; generate for (rd_i = 0; rd_i < DQS_WIDTH; rd_i = rd_i+1) begin: gen_rd_data_sel FDRSE u_ff_rd_data_sel ( .Q (rd_data_sel[rd_i]), .C (clkdiv), .CE (1'b1), .D (cal2_rd_data_sel[rd_i]), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve = 1 */ /* synthesis syn_replicate = 0 */; end endgenerate //***************************************************************** // Max number of taps used for stg2 cal dependent on number of taps // used for stg1 (give priority to stg1 cal - let it use as many // taps as it needs - the remainder of the IDELAY taps can be used // by stg2) //***************************************************************** always @(posedge clkdiv) cal2_idel_tap_limit <= 6'b111111 - cal1_idel_max_tap; //***************************************************************** // second stage calibration uses readback pattern of "1100" (i.e. // 1st rising = 1, 1st falling = 1, 2nd rising = 0, 2nd falling = 0) // only look at the first bit of each DQS group //***************************************************************** // deasserted when captured data has changed since IDELAY was // incremented, or when we're right on the edge (i.e. rise data = // fall data). assign cal2_detect_edge = ((((rdd_rise_q1 != cal2_rd_data_rise_last_pos) || (rdd_fall_q1 != cal2_rd_data_fall_last_pos)) && cal2_rd_data_last_valid_pos && (!cal2_curr_sel)) || (((rdd_rise_q1 != cal2_rd_data_rise_last_neg) || (rdd_fall_q1 != cal2_rd_data_fall_last_neg)) && cal2_rd_data_last_valid_neg && (cal2_curr_sel)) || (rdd_rise_q1 != rdd_fall_q1)); //***************************************************************** // keep track of edge tap counts found, and whether we've // incremented to the maximum number of taps allowed // NOTE: Assume stage 2 cal always increments the tap count (never // decrements) when searching for edge of the data valid window //***************************************************************** always @(posedge clkdiv) if (cal2_state == CAL2_INIT) begin cal2_idel_tap_limit_hit <= 1'b0; cal2_idel_tap_cnt <= 6'b000000; end else if (cal2_dlyce_dqs) begin cal2_idel_tap_cnt <= cal2_idel_tap_cnt + 1; cal2_idel_tap_limit_hit <= (cal2_idel_tap_cnt == cal2_idel_tap_limit - 1); end //***************************************************************** always @(posedge clkdiv) if (rstdiv) begin calib_done[1] <= 1'b0; calib_done_tmp[1] <= 1'bx; calib_err[1] <= 1'b0; count_dqs <= 'b0; next_count_dqs <= 'b0; cal2_dlyce_dqs <= 1'b0; cal2_dlyinc_dqs <= 1'b0; cal2_idel_dec_cnt <= 6'bxxxxxx; cal2_rd_data_last_valid_neg <= 1'bx; cal2_rd_data_last_valid_pos <= 1'bx; cal2_rd_data_sel <= 'b0; cal2_ref_req <= 1'b0; cal2_state <= CAL2_IDLE; end else begin cal2_ref_req <= 1'b0; cal2_dlyce_dqs <= 1'b0; cal2_dlyinc_dqs <= 1'b0; case (cal2_state) CAL2_IDLE: begin count_dqs <= 'b0; next_count_dqs <= 'b0; if (calib_start[1]) begin cal2_rd_data_sel <= {DQS_WIDTH{1'b0}}; calib_done[1] <= 1'b0; calib_done_tmp[1] <= 1'b0; cal2_state <= CAL2_INIT; end end // Pass through this state every time we calibrate a new DQS group CAL2_INIT: begin cal2_curr_sel <= 1'b0; cal2_rd_data_last_valid_neg <= 1'b0; cal2_rd_data_last_valid_pos <= 1'b0; cal2_state <= CAL2_INIT_IDEL_WAIT; end // Stall state only used if calibration run more than once. Can take // this state out if design never runs calibration more than once. // We need this state to give time for MUX'ed data to settle after // resetting RD_DATA_SEL CAL2_INIT_IDEL_WAIT: if (!idel_set_wait) cal2_state <= CAL2_FIND_EDGE_POS; // Look for an edge - first check "positive-edge" stage 2 capture CAL2_FIND_EDGE_POS: begin // if found an edge, then switch to the opposite edge stage 2 // capture and we're done - no need to decrement the tap count, // since switching to the opposite edge will shift the capture // point by 180 degrees if (cal2_detect_edge) begin cal2_curr_sel <= 1'b1; cal2_state <= CAL2_DONE; // set all DQS groups to be the same for simulation if (SIM_ONLY != 0) cal2_rd_data_sel <= {DQS_WIDTH{1'b1}}; else cal2_rd_data_sel[count_dqs] <= 1'b1; if ((count_dqs == DQS_WIDTH-1) || (SIM_ONLY != 0)) calib_done_tmp[1] <= 1'b1; else // MIG 2.1: Fix for simulation out-of-bounds error when // SIM_ONLY=0, and DQS_WIDTH=(power of 2) (needed for VHDL) next_count_dqs <= count_dqs + 1; end else begin // otherwise, invert polarity of stage 2 capture and look for // an edge with opposite capture clock polarity cal2_curr_sel <= 1'b1; cal2_rd_data_sel[count_dqs] <= 1'b1; cal2_state <= CAL2_FIND_EDGE_IDEL_WAIT_POS; cal2_rd_data_rise_last_pos <= rdd_rise_q1; cal2_rd_data_fall_last_pos <= rdd_fall_q1; cal2_rd_data_last_valid_pos <= 1'b1; end end // Give time to switch from positive-edge to negative-edge second // stage capture (need time for data to filter though pipe stages) CAL2_FIND_EDGE_IDEL_WAIT_POS: if (!idel_set_wait) cal2_state <= CAL2_FIND_EDGE_NEG; // Look for an edge - check "negative-edge" stage 2 capture CAL2_FIND_EDGE_NEG: if (cal2_detect_edge) begin cal2_curr_sel <= 1'b0; cal2_state <= CAL2_DONE; // set all DQS groups to be the same for simulation if (SIM_ONLY != 0) cal2_rd_data_sel <= {DQS_WIDTH{1'b0}}; else cal2_rd_data_sel[count_dqs] <= 1'b0; if ((count_dqs == DQS_WIDTH-1) || (SIM_ONLY != 0)) calib_done_tmp[1] <= 1'b1; else // MIG 2.1: Fix for simulation out-of-bounds error when // SIM_ONLY=0, and DQS_WIDTH=(power of 2) (needed for VHDL) next_count_dqs <= count_dqs + 1; end else if (cal2_idel_tap_limit_hit) begin // otherwise, if we've run out of taps, then immediately // backoff by half # of taps used - that's our best estimate // for optimal calibration point. Doesn't matter whether which // polarity we're using for capture (we don't know which one is // best to use) cal2_idel_dec_cnt <= {1'b0, cal2_idel_tap_limit[5:1]}; cal2_state <= CAL2_DEC_IDEL; if ((count_dqs == DQS_WIDTH-1) || (SIM_ONLY != 0)) calib_done_tmp[1] <= 1'b1; else // MIG 2.1: Fix for simulation out-of-bounds error when // SIM_ONLY=0, and DQS_WIDTH=(power of 2) (needed for VHDL) next_count_dqs <= count_dqs + 1; end else begin // otherwise, increment IDELAY, and start looking for edge again cal2_curr_sel <= 1'b0; cal2_rd_data_sel[count_dqs] <= 1'b0; cal2_state <= CAL2_FIND_EDGE_IDEL_WAIT_NEG; cal2_rd_data_rise_last_neg <= rdd_rise_q1; cal2_rd_data_fall_last_neg <= rdd_fall_q1; cal2_rd_data_last_valid_neg <= 1'b1; cal2_dlyce_dqs <= 1'b1; cal2_dlyinc_dqs <= 1'b1; end CAL2_FIND_EDGE_IDEL_WAIT_NEG: if (!idel_set_wait) cal2_state <= CAL2_FIND_EDGE_POS; // if no edge found, then decrement by half # of taps used CAL2_DEC_IDEL: begin if (cal2_idel_dec_cnt == 6'b000000) cal2_state <= CAL2_DONE; else begin cal2_idel_dec_cnt <= cal2_idel_dec_cnt - 1; cal2_dlyce_dqs <= 1'b1; cal2_dlyinc_dqs <= 1'b0; end end // delay state to allow count_dqs and ISERDES data to point to next // DQ bit (DQS group) before going to INIT CAL2_DONE: if (!idel_set_wait) begin count_dqs <= next_count_dqs; if (calib_done_tmp[1]) begin calib_done[1] <= 1'b1; cal2_state <= CAL2_IDLE; end else begin // request auto-refresh after every DQS group calibrated to // avoid tRAS violation cal2_ref_req <= 1'b1; if (calib_ref_done) cal2_state <= CAL2_INIT; end end endcase end //*************************************************************************** // Stage 3 calibration: Read Enable // Description: // read enable calibration determines the "round-trip" time (in # of CLK0 // cycles) between when a read command is issued by the controller, and // when the corresponding read data is synchronized by into the CLK0 domain // this is a long delay chain to delay read enable signal from controller/ // initialization logic (i.e. this is used for both initialization and // during normal controller operation). Stage 3 calibration logic decides // which delayed version is appropriate to use (which is affected by the // round trip delay of DQ/DQS) as a "valid" signal to tell rest of logic // when the captured data output from ISERDES is valid. //*************************************************************************** //***************************************************************** // Delay chains: Use shift registers // Two sets of delay chains are used: // 1. One to delay RDEN from PHY_INIT module for calibration // purposes (delay required for RDEN for calibration is different // than during normal operation) // 2. One per DQS group to delay RDEN from controller for normal // operation - the value to delay for each DQS group can be different // as is determined during calibration //***************************************************************** //***************************************************************** // First delay chain, use only for calibration // input = asserted on rising edge of RDEN from PHY_INIT module //***************************************************************** always @(posedge clk) begin ctrl_rden_r <= ctrl_rden; phy_init_rden_r <= phy_init_rden; phy_init_rden_r1 <= phy_init_rden_r; calib_rden_edge_r <= phy_init_rden_r & ~phy_init_rden_r1; end // Calibration shift register used for both Stage 3 and Stage 4 cal // (not strictly necessary for stage 4, but use as an additional check // to make sure we're checking for correct data on the right clock cycle) always @(posedge clkdiv) if (!calib_done[2]) calib_rden_srl_a <= cal3_rden_srl_a; else calib_rden_srl_a <= cal4_rden_srl_a; // Flops for targetting of multi-cycle path in UCF genvar cal_rden_ff_i; generate for (cal_rden_ff_i = 0; cal_rden_ff_i < 5; cal_rden_ff_i = cal_rden_ff_i+1) begin: gen_cal_rden_dly FDRSE u_ff_cal_rden_dly ( .Q (calib_rden_srl_a_r[cal_rden_ff_i]), .C (clkdiv), .CE (1'b1), .D (calib_rden_srl_a[cal_rden_ff_i]), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve = 1 */ /* synthesis syn_replicate = 0 */; end endgenerate SRLC32E u_calib_rden_srl ( .Q (calib_rden_srl_out), .Q31 (), .A (calib_rden_srl_a_r), .CE (1'b1), .CLK (clk), .D (calib_rden_edge_r) ); FDRSE u_calib_rden_srl_out_r ( .Q (calib_rden_srl_out_r), .C (clk), .CE (1'b1), .D (calib_rden_srl_out), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve = 1 */; // convert to CLKDIV domain. Two version are generated because we need // to be able to tell exactly which fast (clk) clock cycle the read // enable was asserted in. Only one of CALIB_DATA_VALID or // CALIB_DATA_VALID_STGD will be asserted for any given shift value always @(posedge clk) calib_rden_srl_out_r1 <= calib_rden_srl_out_r; always @(posedge clkdiv) begin calib_rden_valid <= calib_rden_srl_out_r; calib_rden_valid_stgd <= calib_rden_srl_out_r1; end //***************************************************************** // Second set of delays chain, use for normal reads // input = RDEN from controller //***************************************************************** // Flops for targetting of multi-cycle path in UCF genvar rden_ff_i; generate for (rden_ff_i = 0; rden_ff_i < 5*DQS_WIDTH; rden_ff_i = rden_ff_i+1) begin: gen_rden_dly FDRSE u_ff_rden_dly ( .Q (rden_dly_r[rden_ff_i]), .C (clkdiv), .CE (1'b1), .D (rden_dly[rden_ff_i]), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve = 1 */ /* synthesis syn_replicate = 0 */; end endgenerate // NOTE: Comment this section explaining purpose of SRL's genvar rden_i; generate for (rden_i = 0; rden_i < DQS_WIDTH; rden_i = rden_i + 1) begin: gen_rden SRLC32E u_rden_srl ( .Q (rden_srl_out[rden_i]), .Q31 (), .A ({rden_dly_r[(rden_i*5)+4], rden_dly_r[(rden_i*5)+3], rden_dly_r[(rden_i*5)+2], rden_dly_r[(rden_i*5)+1], rden_dly_r[(rden_i*5)]}), .CE (1'b1), .CLK (clk), .D (ctrl_rden_r) ); FDRSE u_calib_rden_r ( .Q (calib_rden[rden_i]), .C (clk), .CE (1'b1), .D (rden_srl_out[rden_i]), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve = 1 */; end endgenerate //***************************************************************** // indicates that current received data is the correct pattern. Check both // rising and falling data for first DQ in each DQS group. Note that // we're checking using a pipelined version of read data, so need to take // this inherent delay into account in determining final read valid delay // Data is written to the memory in the following order (first -> last): // 0x1, 0xE, 0xE, 0x1, 0x1, 0xE, 0x1, 0xE // Looking at the two LSb bits, expect data in sequence (in binary): // bit[0]: 1, 0, 0, 1, 0, 1, 0, 1 // bit[1]: 0, 1, 1, 0, 1, 0, 1, 0 // Check for the presence of the first 7 words, and compensate read valid // delay accordingly. Don't check last falling edge data, it may be // corrupted by the DQS tri-state glitch at end of read postamble // (glitch protection not yet active until stage 4 cal) //***************************************************************** always @(posedge clkdiv) begin rdd_rise_q1_r <= rdd_rise_q1; rdd_fall_q1_r <= rdd_fall_q1; rdd_rise_q2_r <= rdd_rise_q2; rdd_fall_q2_r <= rdd_fall_q2; rdd_rise_q1_r1 <= rdd_rise_q1_r; rdd_fall_q1_r1 <= rdd_fall_q1_r; // MIG 3.3: Added comparison for second bit in DQS group for stage 3 cal rdd_rise_q1_bit1_r <= rdd_rise_q1_bit1; rdd_fall_q1_bit1_r <= rdd_fall_q1_bit1; rdd_rise_q2_bit1_r <= rdd_rise_q2_bit1; rdd_fall_q2_bit1_r <= rdd_fall_q2_bit1; rdd_rise_q1_bit1_r1 <= rdd_rise_q1_bit1_r; rdd_fall_q1_bit1_r1 <= rdd_fall_q1_bit1_r; end always @(posedge clkdiv) begin // For the following sequence from memory: // rise[0], fall[0], rise[1], fall[1] // if data is aligned out of fabric ISERDES: // RDD_RISE_Q2 = rise[0] // RDD_FALL_Q2 = fall[0] // RDD_RISE_Q1 = rise[1] // RDD_FALL_Q1 = fall[1] cal3_data_match <= ((rdd_rise_q2_r == 1) && (rdd_fall_q2_r == 0) && (rdd_rise_q1_r == 0) && (rdd_fall_q1_r == 1) && (rdd_rise_q2 == 0) && (rdd_fall_q2 == 1) && (rdd_rise_q1 == 0) && (rdd_rise_q2_bit1_r == 0) && (rdd_fall_q2_bit1_r == 1) && (rdd_rise_q1_bit1_r == 1) && (rdd_fall_q1_bit1_r == 0) && (rdd_rise_q2_bit1 == 1) && (rdd_fall_q2_bit1 == 0) && (rdd_rise_q1_bit1 == 1)); // if data is staggered out of fabric ISERDES: // RDD_RISE_Q1_R = rise[0] // RDD_FALL_Q1_R = fall[0] // RDD_RISE_Q2 = rise[1] // RDD_FALL_Q2 = fall[1] cal3_data_match_stgd <= ((rdd_rise_q1_r1 == 1) && (rdd_fall_q1_r1 == 0) && (rdd_rise_q2_r == 0) && (rdd_fall_q2_r == 1) && (rdd_rise_q1_r == 0) && (rdd_fall_q1_r == 1) && (rdd_rise_q2 == 0) && (rdd_rise_q1_bit1_r1 == 0) && (rdd_fall_q1_bit1_r1 == 1) && (rdd_rise_q2_bit1_r == 1) && (rdd_fall_q2_bit1_r == 0) && (rdd_rise_q1_bit1_r == 1) && (rdd_fall_q1_bit1_r == 0) && (rdd_rise_q2_bit1 == 1)); end assign cal3_rden_dly = cal3_rden_srl_a - CAL3_RDEN_SRL_DLY_DELTA; assign cal3_data_valid = (calib_rden_valid | calib_rden_valid_stgd); assign cal3_match_found = ((calib_rden_valid && cal3_data_match) || (calib_rden_valid_stgd && cal3_data_match_stgd)); // when calibrating, check to see which clock cycle (after the read is // issued) does the expected data pattern arrive. Record this result // NOTE: Can add error checking here in case valid data not found on any // of the available pipeline stages always @(posedge clkdiv) begin if (rstdiv) begin cal3_rden_srl_a <= 5'bxxxxx; cal3_state <= CAL3_IDLE; calib_done[2] <= 1'b0; calib_err_2[0] <= 1'b0; count_rden <= {DQS_WIDTH{1'b0}}; rden_dly <= {5*DQS_WIDTH{1'b0}}; end else begin case (cal3_state) CAL3_IDLE: begin count_rden <= {DQS_WIDTH{1'b0}}; if (calib_start[2]) begin calib_done[2] <= 1'b0; cal3_state <= CAL3_INIT; end end CAL3_INIT: begin cal3_rden_srl_a <= RDEN_BASE_DELAY; // let SRL pipe clear after loading initial shift value cal3_state <= CAL3_RDEN_PIPE_CLR_WAIT; end CAL3_DETECT: if (cal3_data_valid) // if match found at the correct clock cycle if (cal3_match_found) begin // For simulation, load SRL addresses for all DQS with same value if (SIM_ONLY != 0) begin for (i = 0; i < DQS_WIDTH; i = i + 1) begin: loop_sim_rden_dly rden_dly[(i*5)] <= cal3_rden_dly[0]; rden_dly[(i*5)+1] <= cal3_rden_dly[1]; rden_dly[(i*5)+2] <= cal3_rden_dly[2]; rden_dly[(i*5)+3] <= cal3_rden_dly[3]; rden_dly[(i*5)+4] <= cal3_rden_dly[4]; end end else begin rden_dly[(count_rden*5)] <= cal3_rden_dly[0]; rden_dly[(count_rden*5)+1] <= cal3_rden_dly[1]; rden_dly[(count_rden*5)+2] <= cal3_rden_dly[2]; rden_dly[(count_rden*5)+3] <= cal3_rden_dly[3]; rden_dly[(count_rden*5)+4] <= cal3_rden_dly[4]; end // Use for stage 4 calibration calib_rden_dly[(count_rden*5)] <= cal3_rden_srl_a[0]; calib_rden_dly[(count_rden*5)+1] <= cal3_rden_srl_a[1]; calib_rden_dly[(count_rden*5)+2] <= cal3_rden_srl_a[2]; calib_rden_dly[(count_rden*5)+3] <= cal3_rden_srl_a[3]; calib_rden_dly[(count_rden*5)+4] <= cal3_rden_srl_a[4]; cal3_state <= CAL3_DONE; end else begin // If we run out of stages to shift, without finding correct // result, the stop and assert error if (cal3_rden_srl_a == 5'b11111) begin calib_err_2[0] <= 1'b1; cal3_state <= CAL3_IDLE; end else begin // otherwise, increase the shift value and try again cal3_rden_srl_a <= cal3_rden_srl_a + 1; cal3_state <= CAL3_RDEN_PIPE_CLR_WAIT; end end // give additional time for RDEN_R pipe to clear from effects of // previous pipeline or IDELAY tap change CAL3_RDEN_PIPE_CLR_WAIT: if (calib_rden_pipe_cnt == 5'b00000) cal3_state <= CAL3_DETECT; CAL3_DONE: begin if ((count_rden == DQS_WIDTH-1) || (SIM_ONLY != 0)) begin calib_done[2] <= 1'b1; cal3_state <= CAL3_IDLE; end else begin count_rden <= count_rden + 1; cal3_state <= CAL3_INIT; end end endcase end end //***************************************************************** // Last part of stage 3 calibration - compensate for differences // in delay between different DQS groups. Assume that in the worst // case, DQS groups can only differ by one clock cycle. Data for // certain DQS groups must be delayed by one clock cycle. // NOTE: May need to increase allowable variation to greater than // one clock cycle in certain customer designs. // Algorithm is: // 1. Record shift delay value for DQS[0] // 2. Compare each DQS[x] delay value to that of DQS[0]: // - If different, than record this fact (RDEN_MUX) // - If greater than DQS[0], set RDEN_INC. Assume greater by // one clock cycle only - this is a key assumption, assume no // more than a one clock cycle variation. // - If less than DQS[0], set RDEN_DEC // 3. After calibration is complete, set control for DQS group // delay (CALIB_RDEN_SEL): // - If RDEN_DEC = 1, then assume that DQS[0] is the lowest // delay (and at least one other DQS group has a higher // delay). // - If RDEN_INC = 1, then assume that DQS[0] is the highest // delay (and that all other DQS groups have the same or // lower delay). // - If both RDEN_INC and RDEN_DEC = 1, then flag error // (variation is too high for this algorithm to handle) //***************************************************************** always @(posedge clkdiv) begin if (rstdiv) begin calib_err_2[1] <= 1'b0; calib_rden_sel <= {DQS_WIDTH{1'bx}}; rden_dec <= 1'b0; rden_dly_0 <= 5'bxxxxx; rden_inc <= 1'b0; rden_mux <= {DQS_WIDTH{1'b0}}; end else begin // if a match if found, then store the value of rden_dly if (!calib_done[2]) begin if ((cal3_state == CAL3_DETECT) && cal3_match_found) begin // store the value for DQS[0] as a reference if (count_rden == 0) begin // for simulation, RDEN calibration only happens for DQS[0] // set RDEN_MUX for all DQS groups to be the same as DQS[0] if (SIM_ONLY != 0) rden_mux <= {DQS_WIDTH{1'b0}}; else begin // otherwise, load values for DQS[0] rden_dly_0 <= cal3_rden_srl_a; rden_mux[0] <= 1'b0; end end else if (SIM_ONLY == 0) begin // for all other DQS groups, compare RDEN_DLY delay value with // that of DQS[0] if (rden_dly_0 != cal3_rden_srl_a) begin // record that current DQS group has a different delay // than DQS[0] (the "reference" DQS group) rden_mux[count_rden] <= 1'b1; if (rden_dly_0 > cal3_rden_srl_a) rden_inc <= 1'b1; else if (rden_dly_0 < cal3_rden_srl_a) rden_dec <= 1'b1; // otherwise, if current DQS group has same delay as DQS[0], // then rden_mux[count_rden] remains at 0 (since rden_mux // array contents initialized to 0) end end end end else begin // Otherwise - if we're done w/ stage 2 calibration: // set final value for RDEN data delay // flag error if there's more than one cycle variation from DQS[0] calib_err_2[1] <= (rden_inc && rden_dec); if (rden_inc) // if DQS[0] delay represents max delay calib_rden_sel <= ~rden_mux; else // if DQS[0] delay represents min delay (or all the delays are // the same between DQS groups) calib_rden_sel <= rden_mux; end end end // flag error for stage 3 if appropriate always @(posedge clkdiv) calib_err[2] <= calib_err_2[0] | calib_err_2[1]; //*************************************************************************** // Stage 4 calibration: DQS gate //*************************************************************************** //***************************************************************** // indicates that current received data is the correct pattern. Same as // for READ VALID calibration, except that the expected data sequence is // different since DQS gate is asserted after the 6th word. // Data sequence: // Arrives from memory (at FPGA input) (R, F): 1 0 0 1 1 0 0 1 // After gating the sequence looks like: 1 0 0 1 1 0 1 0 (7th word = // 5th word, 8th word = 6th word) // What is the gate timing is off? Need to make sure we can distinquish // between the results of correct vs. incorrect gate timing. We also use // the "read_valid" signal from stage 3 calibration to help us determine // when to check for a valid sequence for stage 4 calibration (i.e. use // CAL4_DATA_VALID in addition to CAL4_DATA_MATCH/CAL4_DATA_MATCH_STGD) // Note that since the gate signal from the CLK0 domain is synchronized // to the falling edge of DQS, that the effect of the gate will only be // seen starting with a rising edge data (although it is possible // the GATE IDDR output could go metastable and cause a unexpected result // on the first rising and falling edges after the gate is enabled). // Also note that the actual DQS glitch can come more than 0.5*tCK after // the last falling edge of DQS and the constraint for this path is can // be > 0.5*tCK; however, this means when calibrating, the output of the // GATE IDDR may miss the setup time requirement of the rising edge flop // and only meet it for the falling edge flop. Therefore the rising // edge data immediately following the assertion of the gate can either // be a 1 or 0 (can rely on either) // As the timing on the gate is varied, we expect to see (sequence of // captured read data shown below): // - 1 0 0 1 1 0 0 1 (gate is really early, starts and ends before // read burst even starts) // - x 0 0 1 1 0 0 1 (gate pulse starts before the burst, and ends // - x y 0 1 1 0 0 1 sometime during the burst; x,y = 0, or 1, but // - x y x 1 1 0 0 1 all bits that show an x are the same value, // - x y x y 1 0 0 1 and y are the same value) // - x y x y x 0 0 1 // - x y x y x y 0 1 (gate starts just before start of burst) // - 1 0 x 0 x 0 x 0 (gate starts after 1st falling word. The "x" // represents possiblity that gate may not disable // clock for 2nd rising word in time) // - 1 0 0 1 x 1 x 1 (gate starts after 2nd falling word) // - 1 0 0 1 1 0 x 0 (gate starts after 3rd falling word - GOOD!!) // - 1 0 0 1 1 0 0 1 (gate starts after burst is already done) //***************************************************************** assign cal4_data_valid = calib_rden_valid | calib_rden_valid_stgd; assign cal4_data_good = (calib_rden_valid & cal4_data_match) | (calib_rden_valid_stgd & cal4_data_match_stgd); always @(posedge clkdiv) begin // if data is aligned out of fabric ISERDES: cal4_data_match <= ((rdd_rise_q2_r == 1) && (rdd_fall_q2_r == 0) && (rdd_rise_q1_r == 0) && (rdd_fall_q1_r == 1) && (rdd_rise_q2 == 1) && (rdd_fall_q2 == 0) && // MIG 2.1: Last rising edge data value not // guaranteed to be certain value at higher // frequencies // (rdd_rise_q1 == 0) && (rdd_fall_q1 == 0)); // if data is staggered out of fabric ISERDES: cal4_data_match_stgd <= ((rdd_rise_q1_r1 == 1) && (rdd_fall_q1_r1 == 0) && (rdd_rise_q2_r == 0) && (rdd_fall_q2_r == 1) && (rdd_rise_q1_r == 1) && (rdd_fall_q1_r == 0) && // MIG 2.1: Last rising edge data value not // guaranteed to be certain value at higher // frequencies // (rdd_rise_q2 == 0) && (rdd_fall_q2 == 0)); end //***************************************************************** // DQS gate enable generation: // This signal gets synchronized to DQS domain, and drives IDDR // register that in turn asserts/deasserts CE to all 4 or 8 DQ // IDDR's in that DQS group. // 1. During normal (post-cal) operation, this is only for 2 clock // cycles following the end of a burst. Check for falling edge // of RDEN. But must also make sure NOT assert for a read-idle- // read (two non-consecutive reads, separated by exactly one // idle cycle) - in this case, don't assert the gate because: // (1) we don't have enough time to deassert the gate before the // first rising edge of DQS for second burst (b/c of fact // that DQS gate is generated in the fabric only off rising // edge of CLK0 - if we somehow had an ODDR in fabric, we // could pull this off, (2) assumption is that the DQS glitch // will not rise enough to cause a glitch because the // post-amble of the first burst is followed immediately by // the pre-amble of the next burst // 2. During stage 4 calibration, assert for 3 clock cycles // (assert gate enable one clock cycle early), since we gate out // the last two words (in addition to the crap on the DQ bus after // the DQS read postamble). // NOTE: PHY_INIT_RDEN and CTRL_RDEN have slightly different timing w/r // to when they are asserted w/r to the start of the read burst // (PHY_INIT_RDEN is one cycle earlier than CTRL_RDEN). //***************************************************************** // register for timing purposes for fast clock path - currently only // calib_done_r[2] used always @(posedge clk) calib_done_r <= calib_done; always @(*) begin calib_ctrl_rden = ctrl_rden; calib_init_rden = calib_done_r[2] & phy_init_rden; end assign calib_ctrl_rden_negedge = ~calib_ctrl_rden & calib_ctrl_rden_r; // check for read-idle-read before asserting DQS pulse at end of read assign calib_ctrl_gate_pulse = calib_ctrl_rden_negedge_r & ~calib_ctrl_rden; always @(posedge clk) begin calib_ctrl_rden_r <= calib_ctrl_rden; calib_ctrl_rden_negedge_r <= calib_ctrl_rden_negedge; calib_ctrl_gate_pulse_r <= calib_ctrl_gate_pulse; end assign calib_init_gate_pulse = ~calib_init_rden & calib_init_rden_r; always @(posedge clk) begin calib_init_rden_r <= calib_init_rden; calib_init_gate_pulse_r <= calib_init_gate_pulse; calib_init_gate_pulse_r1 <= calib_init_gate_pulse_r; end // Gate is asserted: (1) during cal, for 3 cycles, starting 1 cycle // after falling edge of CTRL_RDEN, (2) during normal ops, for 2 // cycles, starting 2 cycles after falling edge of CTRL_RDEN assign gate_srl_in = ~((calib_ctrl_gate_pulse | calib_ctrl_gate_pulse_r) | (calib_init_gate_pulse | calib_init_gate_pulse_r | calib_init_gate_pulse_r1)); //***************************************************************** // generate DQS enable signal for each DQS group // There are differences between DQS gate signal for calibration vs. during // normal operation: // * calibration gates the second to last clock cycle of the burst, // rather than after the last word (e.g. for a 8-word, 4-cycle burst, // cycle 4 is gated for calibration; during normal operation, cycle // 5 (i.e. cycle after the last word) is gated) // enable for DQS is deasserted for two clock cycles, except when // we have the preamble for the next read immediately following // the postamble of the current read - assume DQS does not glitch // during this time, that it stays low. Also if we did have to gate // the DQS for this case, then we don't have enough time to deassert // the gate in time for the first rising edge of DQS for the second // read //***************************************************************** // Flops for targetting of multi-cycle path in UCF genvar gate_ff_i; generate for (gate_ff_i = 0; gate_ff_i < 5*DQS_WIDTH; gate_ff_i = gate_ff_i+1) begin: gen_gate_dly FDRSE u_ff_gate_dly ( .Q (gate_dly_r[gate_ff_i]), .C (clkdiv), .CE (1'b1), .D (gate_dly[gate_ff_i]), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve = 1 */ /* synthesis syn_replicate = 0 */; end endgenerate genvar gate_i; generate for (gate_i = 0; gate_i < DQS_WIDTH; gate_i = gate_i + 1) begin: gen_gate SRLC32E u_gate_srl ( .Q (gate_srl_out[gate_i]), .Q31 (), .A ({gate_dly_r[(gate_i*5)+4], gate_dly_r[(gate_i*5)+3], gate_dly_r[(gate_i*5)+2], gate_dly_r[(gate_i*5)+1], gate_dly_r[(gate_i*5)]}), .CE (1'b1), .CLK (clk), .D (gate_srl_in) ); // For GATE_BASE_DELAY > 0, have one extra cycle to register outputs // from controller before generating DQS gate pulse. In PAR, the // location of the controller logic can be far from the DQS gate // logic (DQS gate logic located near the DQS I/O's), contributing // to large net delays. Registering the controller outputs for // CL >= 4 (above 200MHz) adds a stage of pipelining to reduce net // delays if (GATE_BASE_DELAY > 0) begin: gen_gate_base_dly_gt3 // add flop between SRL32 and EN_DQS flop (which is located near the // DDR2 IOB's) FDRSE u_gate_srl_ff ( .Q (gate_srl_out_r[gate_i]), .C (clk), .CE (1'b1), .D (gate_srl_out[gate_i]), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve = 1 */; end else begin: gen_gate_base_dly_le3 assign gate_srl_out_r[gate_i] = gate_srl_out[gate_i]; end FDRSE u_en_dqs_ff ( .Q (en_dqs[gate_i]), .C (clk), .CE (1'b1), .D (gate_srl_out_r[gate_i]), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve = 1 */ /* synthesis syn_replicate = 0 */; end endgenerate //***************************************************************** // Find valid window: keep track of how long we've been in the same data // window. If it's been long enough, then declare that we've found a stable // valid window - in particular, that we're past any region of instability // associated with the edge of the window. Use only when finding left edge //***************************************************************** always @(posedge clkdiv) // reset before we start to look for window if (cal4_state == CAL4_INIT) begin cal4_window_cnt <= 4'b0000; cal4_stable_window <= 1'b0; end else if ((cal4_state == CAL4_FIND_EDGE) && cal4_seek_left) begin // if we're looking for left edge, and incrementing IDELAY, count // consecutive taps over which we're in the window if (cal4_data_valid) begin if (cal4_data_good) cal4_window_cnt <= cal4_window_cnt + 1; else cal4_window_cnt <= 4'b0000; end if (cal4_window_cnt == MIN_WIN_SIZE-1) cal4_stable_window <= 1'b1; end //***************************************************************** // keep track of edge tap counts found, and whether we've // incremented to the maximum number of taps allowed //***************************************************************** always @(posedge clkdiv) if ((cal4_state == CAL4_INIT) || cal4_dlyrst_gate) begin cal4_idel_max_tap <= 1'b0; cal4_idel_bit_tap <= 1'b0; cal4_idel_tap_cnt <= 6'b000000; end else if (cal4_dlyce_gate) begin if (cal4_dlyinc_gate) begin cal4_idel_tap_cnt <= cal4_idel_tap_cnt + 1; cal4_idel_bit_tap <= (cal4_idel_tap_cnt == CAL4_IDEL_BIT_VAL-2); cal4_idel_max_tap <= (cal4_idel_tap_cnt == 6'b111110); end else begin cal4_idel_tap_cnt <= cal4_idel_tap_cnt - 1; cal4_idel_bit_tap <= 1'b0; cal4_idel_max_tap <= 1'b0; end end always @(posedge clkdiv) if ((cal4_state != CAL4_RDEN_PIPE_CLR_WAIT) && (cal3_state != CAL3_RDEN_PIPE_CLR_WAIT)) calib_rden_pipe_cnt <= CALIB_RDEN_PIPE_LEN-1; else calib_rden_pipe_cnt <= calib_rden_pipe_cnt - 1; //***************************************************************** // Stage 4 cal state machine //***************************************************************** always @(posedge clkdiv) if (rstdiv) begin calib_done[3] <= 1'b0; calib_done_tmp[3] <= 1'b0; calib_err[3] <= 1'b0; count_gate <= 'b0; gate_dly <= 'b0; next_count_gate <= 'b0; cal4_idel_adj_cnt <= 6'bxxxxxx; cal4_dlyce_gate <= 1'b0; cal4_dlyinc_gate <= 1'b0; cal4_dlyrst_gate <= 1'b0; // reset handled elsewhere in code cal4_gate_srl_a <= 5'bxxxxx; cal4_rden_srl_a <= 5'bxxxxx; cal4_ref_req <= 1'b0; cal4_seek_left <= 1'bx; cal4_state <= CAL4_IDLE; end else begin cal4_ref_req <= 1'b0; cal4_dlyce_gate <= 1'b0; cal4_dlyinc_gate <= 1'b0; cal4_dlyrst_gate <= 1'b0; case (cal4_state) CAL4_IDLE: begin count_gate <= 'b0; next_count_gate <= 'b0; if (calib_start[3]) begin gate_dly <= 'b0; calib_done[3] <= 1'b0; cal4_state <= CAL4_INIT; end end CAL4_INIT: begin // load: (1) initial value of gate delay SRL, (2) appropriate // value of RDEN SRL (so that we get correct "data valid" timing) cal4_gate_srl_a <= GATE_BASE_INIT; cal4_rden_srl_a <= {calib_rden_dly[(count_gate*5)+4], calib_rden_dly[(count_gate*5)+3], calib_rden_dly[(count_gate*5)+2], calib_rden_dly[(count_gate*5)+1], calib_rden_dly[(count_gate*5)]}; // let SRL pipe clear after loading initial shift value cal4_state <= CAL4_RDEN_PIPE_CLR_WAIT; end // sort of an initial state - start checking to see whether we're // already in the window or not CAL4_FIND_WINDOW: // decide right away if we start in the proper window - this // determines if we are then looking for the left (trailing) or // right (leading) edge of the data valid window if (cal4_data_valid) begin // if we find a match - then we're already in window, now look // for left edge. Otherwise, look for right edge of window cal4_seek_left <= cal4_data_good; cal4_state <= CAL4_FIND_EDGE; end CAL4_FIND_EDGE: // don't do anything until the exact clock cycle when to check that // readback data is valid or not if (cal4_data_valid) begin // we're currently in the window, look for left edge of window if (cal4_seek_left) begin // make sure we've passed the right edge before trying to detect // the left edge (i.e. avoid any edge "instability") - else, we // may detect an "false" edge too soon. By design, if we start in // the data valid window, always expect at least // MIN(BIT_TIME_TAPS,32) (-/+ jitter, see below) taps of valid // window before we hit the left edge (this is because when stage // 4 calibration first begins (i.e., gate_dly = 00, and IDELAY = // 00), we're guaranteed to NOT be in the window, and we always // start searching for MIN(BIT_TIME_TAPS,32) for the right edge // of window. If we don't find it, increment gate_dly, and if we // now start in the window, we have at least approximately // CLK_PERIOD-MIN(BIT_TIME_TAPS,32) = MIN(BIT_TIME_TAPS,32) taps. // It's approximately because jitter, noise, etc. can bring this // value down slightly. Because of this (although VERY UNLIKELY), // we have to protect against not decrementing IDELAY below 0 // during adjustment phase). if (cal4_stable_window && !cal4_data_good) begin // found left edge of window, dec by MIN(BIT_TIME_TAPS,32) cal4_idel_adj_cnt <= CAL4_IDEL_BIT_VAL; cal4_idel_adj_inc <= 1'b0; cal4_state <= CAL4_ADJ_IDEL; end else begin // Otherwise, keep looking for left edge: if (cal4_idel_max_tap) begin // ran out of taps looking for left edge (max=63) - happens // for low frequency case, decrement by 32 cal4_idel_adj_cnt <= 6'b100000; cal4_idel_adj_inc <= 1'b0; cal4_state <= CAL4_ADJ_IDEL; end else begin cal4_dlyce_gate <= 1'b1; cal4_dlyinc_gate <= 1'b1; cal4_state <= CAL4_IDEL_WAIT; end end end else begin // looking for right edge of window: // look for the first match - this means we've found the right // (leading) edge of the data valid window, increment by // MIN(BIT_TIME_TAPS,32) if (cal4_data_good) begin cal4_idel_adj_cnt <= CAL4_IDEL_BIT_VAL; cal4_idel_adj_inc <= 1'b1; cal4_state <= CAL4_ADJ_IDEL; end else begin // Otherwise, keep looking: // only look for MIN(BIT_TIME_TAPS,32) taps for right edge, // if we haven't found it, then inc gate delay, try again if (cal4_idel_bit_tap) begin // if we're already maxed out on gate delay, then error out // (simulation only - calib_err isn't currently connected) if (cal4_gate_srl_a == 5'b11111) begin calib_err[3] <= 1'b1; cal4_state <= CAL4_IDLE; end else begin // otherwise, increment gate delay count, and start // over again cal4_gate_srl_a <= cal4_gate_srl_a + 1; cal4_dlyrst_gate <= 1'b1; cal4_state <= CAL4_RDEN_PIPE_CLR_WAIT; end end else begin // keep looking for right edge cal4_dlyce_gate <= 1'b1; cal4_dlyinc_gate <= 1'b1; cal4_state <= CAL4_IDEL_WAIT; end end end end // wait for GATE IDELAY to settle, after reset or increment CAL4_IDEL_WAIT: begin // For simulation, load SRL addresses for all DQS with same value if (SIM_ONLY != 0) begin for (i = 0; i < DQS_WIDTH; i = i + 1) begin: loop_sim_gate_dly gate_dly[(i*5)+4] <= cal4_gate_srl_a[4]; gate_dly[(i*5)+3] <= cal4_gate_srl_a[3]; gate_dly[(i*5)+2] <= cal4_gate_srl_a[2]; gate_dly[(i*5)+1] <= cal4_gate_srl_a[1]; gate_dly[(i*5)] <= cal4_gate_srl_a[0]; end end else begin gate_dly[(count_gate*5)+4] <= cal4_gate_srl_a[4]; gate_dly[(count_gate*5)+3] <= cal4_gate_srl_a[3]; gate_dly[(count_gate*5)+2] <= cal4_gate_srl_a[2]; gate_dly[(count_gate*5)+1] <= cal4_gate_srl_a[1]; gate_dly[(count_gate*5)] <= cal4_gate_srl_a[0]; end // check to see if we've found edge of window if (!idel_set_wait) cal4_state <= CAL4_FIND_EDGE; end // give additional time for RDEN_R pipe to clear from effects of // previous pipeline (and IDELAY reset) CAL4_RDEN_PIPE_CLR_WAIT: begin // MIG 2.2: Bug fix - make sure to update GATE_DLY count, since // possible for FIND_EDGE->RDEN_PIPE_CLR_WAIT->FIND_WINDOW // transition (i.e. need to make sure the gate count updated in // FIND_EDGE gets reflected in GATE_DLY by the time we reach // state FIND_WINDOW) - previously GATE_DLY only being updated // during state CAL4_IDEL_WAIT if (SIM_ONLY != 0) begin for (i = 0; i < DQS_WIDTH; i = i + 1) begin: loop_sim_gate_dly_pipe gate_dly[(i*5)+4] <= cal4_gate_srl_a[4]; gate_dly[(i*5)+3] <= cal4_gate_srl_a[3]; gate_dly[(i*5)+2] <= cal4_gate_srl_a[2]; gate_dly[(i*5)+1] <= cal4_gate_srl_a[1]; gate_dly[(i*5)] <= cal4_gate_srl_a[0]; end end else begin gate_dly[(count_gate*5)+4] <= cal4_gate_srl_a[4]; gate_dly[(count_gate*5)+3] <= cal4_gate_srl_a[3]; gate_dly[(count_gate*5)+2] <= cal4_gate_srl_a[2]; gate_dly[(count_gate*5)+1] <= cal4_gate_srl_a[1]; gate_dly[(count_gate*5)] <= cal4_gate_srl_a[0]; end // look for new window if (calib_rden_pipe_cnt == 5'b00000) cal4_state <= CAL4_FIND_WINDOW; end // increment/decrement DQS/DQ IDELAY for final adjustment CAL4_ADJ_IDEL: // add underflow protection for corner case when left edge found // using fewer than MIN(BIT_TIME_TAPS,32) taps if ((cal4_idel_adj_cnt == 6'b000000) || (cal4_dlyce_gate && !cal4_dlyinc_gate && (cal4_idel_tap_cnt == 6'b000001))) begin cal4_state <= CAL4_DONE; // stop when all gates calibrated, or gate[0] cal'ed (for sim) if ((count_gate == DQS_WIDTH-1) || (SIM_ONLY != 0)) calib_done_tmp[3] <= 1'b1; else // need for VHDL simulation to prevent out-of-index error next_count_gate <= count_gate + 1; end else begin cal4_idel_adj_cnt <= cal4_idel_adj_cnt - 1; cal4_dlyce_gate <= 1'b1; // whether inc or dec depends on whether left or right edge found cal4_dlyinc_gate <= cal4_idel_adj_inc; end // wait for IDELAY output to settle after decrement. Check current // COUNT_GATE value and decide if we're done CAL4_DONE: if (!idel_set_wait) begin count_gate <= next_count_gate; if (calib_done_tmp[3]) begin calib_done[3] <= 1'b1; cal4_state <= CAL4_IDLE; end else begin // request auto-refresh after every DQS group calibrated to // avoid tRAS violation cal4_ref_req <= 1'b1; if (calib_ref_done) cal4_state <= CAL4_INIT; end end endcase end endmodule